Skocz do zawartości

[Sprzedam] Mikrokotrolery STM: STM8S-Discovery (3szt) ET-STM32 STAMP (2szt), mostki H HIP4080A(9szt)


Pomocna odpowiedź

Witam,

Czas na jesienne porządki 🙂

Mam do sprzedania 2 rodzaje mikrokontrolerów opartych na procesorach STM:

8-bit: STM8S-Discovery

http://www.st.com/mcu/contentid-130-113-STM8S_DISCOVERY.html

Features and benefits

STM8S105C microcontroller

-Uses the most common STM8S reference, with 32 Kbytes of Flash, E²Data and 48 pins

Self powered by USB cable between PC and STM8S-Discovery - Immediate plug-and-play demonstration

- Selectable power supply voltage: 5 V or 3.3 V for your application, Adapts the demo to the future application environment

- Embedded STLink for the STM8S

- USB interface for programming and debugging

- Non-intrusive debug with the in-circuit debugger present on STM8S-Discovery

- SWIM debug support

- Detach the debugger to run the application

- Single wire interface is always available for software upgrade

- Touch sensing interface

- Many demonstrations are available ready to use or constructed from

- Wrapping area for user’s own application

Cena: 30PLN (dostępne 3szt)

32-bit: ET-STM32 STAMP

http://www.futurlec.com/ET-STM32_Stamp.shtml

Features

• Includes ST Microelectronics STM32F103 Microcontroller with 512kb Internal Flash Program Memory

• 32-Bit ARM Cortex M3 Processor Bit running at 72MHz or 90 MIPS

• Direct In-Circuit Program Download with RS-232 Connection

• Up to 48 I/O points

• 16 Channels 12-Bit A/D Converters

• 2 Channels 12-Bit D/A Converters

• 1 CAN Channel

• 5 USARTS and 2 I2C Ports, together with SPI

• Two 32-Bit Timers with Four Capture and Compare Channels

• On-Board Real-Time Clock with External Back-Up Battery Connection

• Power LED and Boot LED's

• Boot Load and Reset Buttons

• Easy to Install and Remove

• Ideal as an Interchangeable Controller for Real-Time Systems

Cena: 70PLN (dostępne 2szt, w zestawie kabel do podpięcia przez RS232 oraz płytka z dokumentacją)

Sterownik mostka H (trudno dostępny w Polsce!): Intersil HIP4080A (obudowa DIP20).

http://www.intersil.com/products/deviceinfo.asp?pn=HIP4080A

Świetny do skonstruowania własnego mostka H, praktycznie wszystko co potrzeba jest w dokumentacji układu i notach aplikacyjnych.

Key Features

* Drives N-Channel FET Full Bridge Including High Side Chop Capability

* Bootstrap Supply Max Voltage to 95VDC

* Drives 1000pF Load at 1MHz in Free Air at +50°C with Rise and Fall Times of Typically 10ns

* User-Programmable Dead Time

* Charge-Pump and Bootstrap Maintain Upper Bias Supplies

* DIS (Disable) Pin Pulls Gates Low

* Input Logic Thresholds Compatible with 5V to 15V Logic Levels

* Very Low Power Consumption

* Undervoltage Protection

* Pb-Free Available as an Option

Description

The HIP4080A is a high frequency, medium voltage Full Bridge N-Channel FET driver IC, available in 20 lead plastic SOIC and DIP packages. The HIP4080A includes an input comparator, used to facilitate the "hysteresis" and PWM modes of operation. Its HEN (high enable) lead can force current to freewheel in the bottom two external power MOSFETs, maintaining the upper power MOSFETs off. Since it can switch at frequencies up to 1MHz, the HIP4080A is well suited for driving Voice Coil Motors, switching power amplifiers and power supplies.

HIP4080A can also drive medium voltage brush motors, and two HIP4080As can be used to drive high performance stepper motors, since the short minimum "on-time" can provide fine micro-stepping capability.

Short propagation delays of approximately 55ns maximize control loop crossover frequencies and dead-times which can be adjusted to near zero to minimize distortion, resulting in precise control of the driven load.

Cena: 30PLN (dostępne 9szt (z czego 2 sztuki akurat mam nie ROHS)

(Preferuję przedpłatę na konto, wysyłką Pocztą Polską. Dla zainteresowanych mogę wystawić aukcję allegro, przy zakupie kilku rzeczy - cena do negocjacji)

Pozdrawiam

Link do komentarza
Share on other sites

Dołącz do dyskusji, napisz odpowiedź!

Jeśli masz już konto to zaloguj się teraz, aby opublikować wiadomość jako Ty. Możesz też napisać teraz i zarejestrować się później.
Uwaga: wgrywanie zdjęć i załączników dostępne jest po zalogowaniu!

Anonim
Dołącz do dyskusji! Kliknij i zacznij pisać...

×   Wklejony jako tekst z formatowaniem.   Przywróć formatowanie

  Dozwolonych jest tylko 75 emoji.

×   Twój link będzie automatycznie osadzony.   Wyświetlać jako link

×   Twoja poprzednia zawartość została przywrócona.   Wyczyść edytor

×   Nie możesz wkleić zdjęć bezpośrednio. Prześlij lub wstaw obrazy z adresu URL.

×
×
  • Utwórz nowe...

Ważne informacje

Ta strona używa ciasteczek (cookies), dzięki którym może działać lepiej. Więcej na ten temat znajdziesz w Polityce Prywatności.