Kubot003 Napisano Luty 18, 2021 Udostępnij Napisano Luty 18, 2021 (edytowany) Witam, zacząłem kurs arduino. Jestem na 2. lekcji, jest tam pierwsze zadanie do wykonania, mianowicie podłączenie diody led z rezystorem i arduino uno (co zrobiłem na 100% dobrze), przepisanie oraz wgranie takiej komendy/programu. Wyskakuje mi błąd: "problem z wgrywaniem na płytkę, sprawdź i link przekierowujący do strony" void setup() { pinMode(8, OUTPUT); digitalWrite(8, HIGH); } void loop() { } Proszę o pomoc bo to moja pierwsza przygoda z arduino oraz takim programowaniem, mam już za sobą podstawy elektroniki opis błędów: Arduino:1.8.12 (Windows 10), Płytka:"Arduino Uno" Szkic używa 712 bajtów (2%) pamięci programu. Maksimum to 32256 bajtów. Zmienne globalne używają 9 bajtów (0%) pamięci dynamicznej, pozostawiając 2039 bajtów dla zmiennych lokalnych. Maksimum to 2048 bajtów. avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x06 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x06 Problem z wgrywaniem na płytkę. Sprawdź http://www.arduino.cc/en/Guide/Troubleshooting#upload w poszukiwaniu sugestii. Ten raport powinien zawierać więcej informacji jeśli w File -> Preferencje zostanie włączona opcja "Pokaż szczegółowe informacje podczas kompilacji" Edytowano Luty 19, 2021 przez Gieneq Cytuj Link do komentarza Share on other sites More sharing options...
Gieneq Luty 19, 2021 Udostępnij Luty 19, 2021 @Kubot003 witam na forum 🙂 Masz pobrany sterownik? Próbowałeś restart komputera, odłączyć i podłączyć Arduino? 1 Cytuj Link do komentarza Share on other sites More sharing options...
Kubot003 Luty 19, 2021 Autor tematu Udostępnij Luty 19, 2021 @Gieneq Bardzo dziękuję 🙂 , nie przyszło mi do głowy aby zainstalować sterowniki. Wszystko działa 😄 1 Cytuj Link do komentarza Share on other sites More sharing options...
Pomocna odpowiedź
Dołącz do dyskusji, napisz odpowiedź!
Jeśli masz już konto to zaloguj się teraz, aby opublikować wiadomość jako Ty. Możesz też napisać teraz i zarejestrować się później.
Uwaga: wgrywanie zdjęć i załączników dostępne jest po zalogowaniu!