Skocz do zawartości

Domoticz nie wykrywa bramki


okos

Pomocna odpowiedź

Witajcie, próbuje podziałać z moim pieszym projektem wzorując się na tym:

http://majsterkowo.pl/domoticz-komunikacja-bezprzewodowa/

Utknąłem jednak nie mogąc dodać bramki w domoticzu, bo "domo" nie wykrywa dev/ttyUSB0 jak u kolegi-autora Michała, tylko dev/ttyAC0 i dev/ttyAMA0

Podpowiedzcie proszę gdzie może leżeć tego przyczyna.

Pozdrawaim

Link do komentarza
Share on other sites

Właśnie chyba za bardzo się do niej przywiązałem, bo w instrukcji podane zostały płytki arduino Leonadro i Nano, które są na AVR Atmega32U4 ( takie właśnie posiadam ), a program z bibliotek MySensors dla bramki jest na atmege 328.

Wycinek z poniższego kodu:

// Hardware profile 
MyHwATMega328 hw;

Chyba, że jest jakaś możliwość dostosowania programu dla którejkolwiek z moich płytek aby użyć jej jako bramki ?

Poniżej umieszczam cały kod:

/**
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2015 Sensnology AB
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
*******************************
*
* DESCRIPTION
* The ArduinoGateway prints data received from sensors on the serial link. 
* The gateway accepts input on seral which will be sent out on radio network.
*
* The GW code is designed for Arduino Nano 328p / 16MHz
*
* Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND  
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
*
* LEDs (OPTIONAL):
* - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error 
* 
*/

#define NO_PORTB_PINCHANGES  

#include <MySigningNone.h>
#include <MyTransportRFM69.h>
#include <MyTransportNRF24.h>
#include <MyHwATMega328.h>
#include <MySigningAtsha204Soft.h>
#include <MySigningAtsha204.h>

#include <SPI.h>  
#include <MyParserSerial.h>  
#include <MySensor.h>  
#include <stdarg.h>
#include <PinChangeInt.h>
#include "GatewayUtil.h"

#define INCLUSION_MODE_TIME 1 // Number of minutes inclusion mode is enabled
#define INCLUSION_MODE_PIN  3 // Digital pin used for inclusion mode button
#define RADIO_ERROR_LED_PIN 4  // Error led pin
#define RADIO_RX_LED_PIN    6  // Receive led pin
#define RADIO_TX_LED_PIN    5  // the PCB, on board LED

// NRFRF24L01 radio driver (set low transmit power by default) 
MyTransportNRF24 transport(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);
//MyTransportRFM69 transport;

// Message signing driver (signer needed if MY_SIGNING_FEATURE is turned on in MyConfig.h)
//MySigningNone signer;
//MySigningAtsha204Soft signer;
//MySigningAtsha204 signer;

// Hardware profile 
MyHwATMega328 hw;

// Construct MySensors library (signer needed if MY_SIGNING_FEATURE is turned on in MyConfig.h)
// To use LEDs blinking, uncomment WITH_LEDS_BLINKING in MyConfig.h
#ifdef WITH_LEDS_BLINKING
MySensor gw(transport, hw /*, signer*/, RADIO_RX_LED_PIN, RADIO_TX_LED_PIN, RADIO_ERROR_LED_PIN);
#else
MySensor gw(transport, hw /*, signer*/);
#endif

char inputString[MAX_RECEIVE_LENGTH] = "";    // A string to hold incoming commands from serial/ethernet interface
int inputPos = 0;
boolean commandComplete = false;  // whether the string is complete

void parseAndSend(char *commandBuffer);

void output(const char *fmt, ... ) {
  va_list args;
  va_start (args, fmt );
  vsnprintf_P(serialBuffer, MAX_SEND_LENGTH, fmt, args);
  va_end (args);
  Serial.print(serialBuffer);
}


void setup()  
{ 
 gw.begin(incomingMessage, 0, true, 0);

 setupGateway(INCLUSION_MODE_PIN, INCLUSION_MODE_TIME, output);

 // Add interrupt for inclusion button to pin
 PCintPort::attachInterrupt(pinInclusion, startInclusionInterrupt, RISING);


 // Send startup log message on serial
 serial(PSTR("0;0;%d;0;%d;Gateway startup complete.\n"),  C_INTERNAL, I_GATEWAY_READY);
}

void loop()  
{ 
 gw.process();

 checkButtonTriggeredInclusion();
 checkInclusionFinished();

 if (commandComplete) {
   // A command wass issued from serial interface
   // We will now try to send it to the actuator
   parseAndSend(gw, inputString);
   commandComplete = false;  
   inputPos = 0;
 }
}


/*
 SerialEvent occurs whenever a new data comes in the
hardware serial RX.  This routine is run between each
time loop() runs, so using delay inside loop can delay
response.  Multiple bytes of data may be available.
*/
void serialEvent() {
 while (Serial.available()) {
   // get the new byte:
   char inChar = (char)Serial.read(); 
   // if the incoming character is a newline, set a flag
   // so the main loop can do something about it:
   if (inputPos<MAX_RECEIVE_LENGTH-1 && !commandComplete) { 
     if (inChar == '\n') {
       inputString[inputPos] = 0;
       commandComplete = true;
     } else {
       // add it to the inputString:
       inputString[inputPos] = inChar;
       inputPos++;
     }
   } else {
      // Incoming message too long. Throw away 
       inputPos = 0;
   }
 }
}



Link do komentarza
Share on other sites

Dołącz do dyskusji, napisz odpowiedź!

Jeśli masz już konto to zaloguj się teraz, aby opublikować wiadomość jako Ty. Możesz też napisać teraz i zarejestrować się później.
Uwaga: wgrywanie zdjęć i załączników dostępne jest po zalogowaniu!

Anonim
Dołącz do dyskusji! Kliknij i zacznij pisać...

×   Wklejony jako tekst z formatowaniem.   Przywróć formatowanie

  Dozwolonych jest tylko 75 emoji.

×   Twój link będzie automatycznie osadzony.   Wyświetlać jako link

×   Twoja poprzednia zawartość została przywrócona.   Wyczyść edytor

×   Nie możesz wkleić zdjęć bezpośrednio. Prześlij lub wstaw obrazy z adresu URL.

×
×
  • Utwórz nowe...

Ważne informacje

Ta strona używa ciasteczek (cookies), dzięki którym może działać lepiej. Więcej na ten temat znajdziesz w Polityce Prywatności.